How to Install Stair Treads and Risers

To install new stair treads and risers, remove the old steps down to the stringers, then work from the bottom up: riser first, then the tread on top of it. Measure and cut every step on its own, set each piece in a bead of construction adhesive, and fasten it with trim screws or finish nails through pilot holes. The adhesive is what keeps the stairs from squeaking later. If you only want to switch carpeted stairs to wood, RetroFit treads glue right on top of the rough framing boards under the carpet and skip most of the demolition.

Full Replacement or RetroFit?

Full replacementRetroFit
What you removeCarpet, the rough treads and risers, down to the stringersCarpet, pad, staples, tack strip and the front edge of each rough tread. The rough treads stay.
Parts1″ solid treads and 3/4″ risersRetroFit kits (thin tread plus riser)
Best forOpen stairs, new layouts, damaged or squeaky stepsCarpeted stairs with solid treads underneath. Return kits finish open sides.
EffortMore demolition and cuttingFaster, less mess

Not sure which tread you need? See the types of stair treads.

Tools You’ll Need

  • Pry bar and hammer
  • Reciprocating saw or oscillating multi-tool
  • Circular saw or miter saw (fine-tooth blade)
  • Table saw or track saw (to rip treads to depth)
  • Stair tread template tool (or a scrap of plywood to make a pattern)
  • Drill/driver and countersink bit
  • Tape measure, speed square and 4′ level
  • Caulk gun
  • Brad or finish nailer (optional)
  • Safety glasses, gloves and a dust mask
  • Shop vac

Parts You’ll Need

Before you start

Let new treads and risers sit in the room for a few days so the wood can adjust to your home. See climate considerations for wood stairs. Many installers also stain and seal the treads before installing them, on all sides and the ends, which helps keep them flat.

Full Replacement: Step by Step

Step 1: Strip the stairs

Remove the carpet, pad, staples and tack strip. If you’re also replacing balusters, cut the old ones in half and twist them out first (see how to install iron balusters). Then pry off the rough treads and risers, working from the top step down. Pull every nail and scrape off old glue so the stringers are clean and flat.

Step 2: Check the stringers

Lay a level across the stringers on each step. If one stringer is low, shim it so the tread will sit flat. A tread that rocks will squeak no matter how well it’s fastened.

Step 3: Measure every step

Measure each step on its own. Walls are rarely square, so measure the width at the back and the front of every step, and cut to match. A stair tread template tool makes this fast: set it to the step, lock it, and trace it onto the tread. Number each step and each piece in pencil as you go.

wallwall TOP VIEW · riser above (back of step) A: width at the back B: width at the front C: depth, riser to frontedge + nosing overhang
Figure 1: Looking down on one step. Measure the width at the back (A) and the front (B) of every step. Walls are rarely perfectly square, so A and B are often a little different.

For depth, measure from the face of the riser above to the front of the stringer, then add your nosing overhang. Most codes want the nosing to stick out 3/4″ to 1-1/4″ past the riser below. See the tread and riser rules in our stair building code guide.

Step 4: Cut the risers and treads

Cut each riser to the width of its step and to height. Cut each tread to length using your template, then rip it to depth from the back edge so the bullnose stays intact. Dry-fit every piece before you glue anything.

Step 5: Install from the bottom up

stringer tread riser nosing overhang3/4″ to 1-1/4″ bead of constructionadhesive on stringer next riser sitson back of tread
Figure 2: How a riser and tread fit together. Work from the bottom step up.
  1. Run a bead of construction adhesive on the stringers for the bottom riser and set the riser in place. Fasten it to the stringers.
  2. Run adhesive along the top of each stringer for the bottom tread. Set the tread so its back edge is tight to where the next riser will go and the nosing overhangs the riser below.
  3. Drill pilot holes and fasten the tread to every stringer with trim-head screws or finish nails. Countersink the screws.
  4. Set the next riser on the back of that tread, glue and fasten it, and repeat up the stairs.

Tip: If you can reach under the stairs, add a few screws up through the back of each tread into the bottom of the riser above. It’s the best squeak prevention there is.

Step 6: Finish the top step and open sides

Use a landing tread at the top step and along any landing or balcony edge, so the floor meets the stairs with the same bullnose as your treads. On an open staircase, use mitered return treads so the end grain doesn’t show.

Step 7: Fill, sand and finish

Fill or plug the screw holes, sand smooth, and stain or seal if you didn’t pre-finish. Caulk the joint between the riser and the tread if you paint the risers. Let the finish cure before you walk on it.

RetroFit: Step by Step

RetroFit treads turn carpeted stairs into hardwood without tearing out the stairs. Under the carpet, each step is a rough tread: a plain framing board, usually 2x lumber, not a finished tread. It stays in place as the base, and the RetroFit tread glues down on top. Always follow the instructions that come with your kit.

Step 1: Strip the carpet

Remove the carpet, pad, staples, tack strip and any nails sticking up. The rough treads must be solid and flat. Screw down any loose or squeaky board. If one is split or soft, replace it with a new 2x board ripped flush with the riser.

Step 2: Cut the rough treads flush

On every step, cut the front edge of the rough tread off flush with the face of the riser (Figure 3). An oscillating multi-tool or a flush-cut saw works well, and a chisel cleans up the corners next to the wall or skirtboard.

1. Cut the rough tread flush cut lineold riserrough tread (framing board) 2. Riser cover, then the RetroFit tread RetroFit tread glued on top of the rough tread thin riser gluedto the old riser urethane adhesive
Figure 3: RetroFit method. The rough tread stays as the base. Only its front edge is cut off.

Step 3: Cover the risers

Glue the thin riser from the kit to the face of the old riser, or install a new riser. If the old risers are in good shape, you can also just paint them.

Step 4: Measure and cut each tread

Measure each step at the front and the back. Cut the RetroFit tread to the width of the step, and to the depth of the rough tread measured from the face of the new riser. Number each tread as you go.

Open end on the step?

If a step is open on the side, plan the return before you cut the tread to depth. Leave the tread 1″ longer for each open end, then miter the end and attach the return nosing piece with wood glue and two finish nails. Fill, sand, and only then trim the tread to depth. Our RetroFit return kits and Young RetroReturn kits include the return piece.

Step 5: Glue the treads down

Glue each tread to the rough tread with a polyurethane (urethane) construction adhesive, in a full zigzag bead. Never use a water-based adhesive with RetroFit treads. Keep foot traffic off until the adhesive cures.

Step 6: Finish

Stain or seal the treads if they came unfinished, and finish the top step with a matching landing tread.

Check the first and last step

Every tread goes up by the same amount, so the steps in the middle stay even. Only the bottom and top steps change a little. Measure those two before you start. See the stair code guide.

Shop by Step Size

Want a pro to do it? See what it costs to have treads and risers installed.

Stair Tread Install FAQ

Do you install the riser or the tread first?

Work from the bottom up, riser first. Set the bottom riser, then the bottom tread, then the next riser sitting on the back of that tread, and so on up the stairs.

Should I glue or nail stair treads?

Both. Construction adhesive on the stringers stops squeaks, and screws or finish nails hold the tread tight while the glue cures. Drill pilot holes so the wood doesn’t split.

How much should a stair tread overhang the riser?

Most codes call for a nosing of 3/4″ to 1-1/4″ past the riser below. Check your local code.

How do I cut treads when my walls aren’t square?

Measure the width at the front and back of every step, or use a stair tread template tool to copy the exact shape onto the tread before you cut.

Can I put new treads over my old ones?

Only with RetroFit treads, which are made thin for that. Stacking full 1″ treads on top of old ones throws off your step heights. Either way, check the top and bottom risers against code.

Should I stain treads before or after installing?

Either works. Finishing before install is easier and lets you seal every side, which helps keep the treads flat. Finishing after hides fill and touch-ups better.

Free Shipping Over $750Free ground shipping on parts orders to the lower 48 states.
Secure PaymentAll major credit cards and PayPal.
Call a Stair Expert(866) 727-9356, M–F 8a–3p CST, or get a free quote.
We Beat Competitors by 5%Send us a competitor quote and we'll beat it.